Silverado & Avalanche LED Headlight Installation Guide — BLH0002004

INSTALLATION & SUPPORT · MANUAL BLH0002004

Follow this guide to install your Hawkglow LED headlight and turn signal assemblies. Review the original manual before starting and confirm your vehicle's compatibility on the product page.

VIEW INSTALLATION MANUAL ↓

Before you start

Disconnect the main fuse or negative battery terminal before beginning work. Seek professional assistance if you do not have experience with automotive electrical work or headlight installation.

Test only one side at a time. Black wire = ground (−); red wire = positive (+). Do not open the light housing without the proper heating and sealing procedures.

This is an installation guide, not a complete fitment list. Confirm vehicle compatibility on the product page.

Install the headlight and turn signal assemblies

  1. Remove the original assemblies. Engage the parking brake, open the hood, rotate and remove the headlight retaining pins, pull the headlight outward and disconnect its wiring harness. Release the turn signal retaining clip and disconnect that assembly.
  2. Connect and test the low beams. Start with the driver side, then repeat on the passenger side.
  3. Connect and test the high beams. Start with the driver side, then repeat on the passenger side.
  4. Connect the DRL jumpers. Join the headlight and turn signal DRL jumpers. Connect the driver-side DRL connector to the vehicle and test, then repeat on the passenger side.
  5. Connect the turn signals. Test the parking lights and turn signals, one side at a time.
  6. Protect the wiring and mount the assemblies. Secure exposed wiring and connectors with heat-shrink tubing or fabric wire loom tape as needed. Use the factory mounting hardware. For the turn signal, insert the side nearest the horn first, then press until it snaps into place.
  7. Aim and verify. Adjust the headlights and verify all lighting functions before closing the hood.
Nine headlight removal and installation photographs from manual printed page 02View full-size image ↗
Headlight installation photographs · Manual page 02. See the PDF for the separate turn signal photographs on page 03.

Identify the connectors

Use the numbered diagram to identify each lead before making connections.

Numbered headlight and turn signal wiring diagram, with DRL jumpers and fuse harnessView full-size image ↗
No. Connection No. Connection
1 Low beam 6 Turn signal
2 High beam 7 DRL jumper B
3 DRL jumper A 8 ACC/DRL connector
4 DRL connector 9 DRL fuse harness
5 Resistor

Source: manual page 05.

If the factory DRL connection does not activate the DRLs

The manual instructs you to use the supplied DRL fuse harness to connect the DRLs to ACC power.

  1. Connect the high/low beam and turn signal connectors to the matching vehicle harness connectors.
  2. Connect the turn signal ACC/DRL connectors to the matching connectors on the DRL fuse harness.
  3. Locate the under-hood fuse box and use the manual’s fuse reference table and diagrams to identify the corresponding fuse slot.
Vehicle listed in the manual Fuse reference
2003–2004 Silverado 1500 / 2500 / 3500 54
2005 Silverado 1500 / 2500 / 3500 CIG LTR
2006 Silverado 1500 / 2500 / 3500 69
2003–2006 Avalanche 45
Vehicle not listed? Contact support with your vehicle’s year, make and model. This manual does not provide a fuse reference for 2007 Silverado Classic applications.
Original DRL-to-ACC harness connections and under-hood fuse reference photographs from manual page 06View full-size image ↗

Aim the headlights after installation

The manual describes a wall-based procedure at 25 ft (7.6 m), using the vertical adjustment screws on the rear of each housing. It calls for a level surface, correct tire pressure, removal of excess cargo and adjustment of one headlight at a time.

Consult the complete aiming procedure and diagrams on manual page 07 before adjustment. Seek professional assistance if you are unfamiliar with headlight aiming.

Troubleshooting

High or low beam does not work

The manual identifies connector polarity as a possible cause. Disconnect the relevant connector, rotate it 180°, reconnect and retest. Test each headlight individually.

The headlights stay in high-beam mode

The manual identifies a negative-switched headlight circuit as a possible cause. If connector polarity adjustment does not resolve the issue, contact support.

Only one DRL section illuminates

For only the upper or lower DRL lighting in DRL mode, the manual recommends checking DRL connector polarity. If the lower DRL does not illuminate with the high or low beams on, check that the DRL jumpers are securely connected.

The side marker does not illuminate

Verify turn signal operation first. The manual then recommends checking turn signal connector polarity. The upper side marker section is a reflector only.

The turn signals flash rapidly

The manual recommends a compatible LED flasher relay, which is not included. Confirm compatibility before replacement.

If no lights work after polarity adjustments, check the fuse and all wiring connections. Source: manual page 08.

Routine maintenance

Clean with water and mild car soap when needed, then dry with a microfiber towel. Avoid abrasive cleaners and materials.

Temporary condensation may occur with temperature and humidity changes. If water remains, accumulates or enters through a leak, discontinue use and contact support.

KEEP A COPY

Download the original installation manual

Open the original manual in a new tab to view, save or print all installation diagrams and instructions.

Car Light User Manual

BLH0002004 · English · PDF · 12 pages · 3.14 MB

VIEW / DOWNLOAD PDF ↗

Need help? contact@hawkglow.com

← Back to the Silverado / Avalanche product