Silverado, Suburban & Tahoe LED Headlight Installation Guide — BLH0002005

INSTALLATION & SUPPORT · MANUAL BLH0002005

Use this guide to install your Hawkglow LED headlight and turn signal assemblies for compatible Chevy Silverado, Suburban and Tahoe models. Confirm your vehicle's fitment and review the original manual before starting.

VIEW INSTALLATION MANUAL ↓

Vehicle compatibility

Vehicle Years and models listed in the manual
Chevy Silverado 1999–2002 Silverado 1500 / 2500
Chevy Silverado HD / 3500 2001–2002 Silverado 1500 HD / 2500 HD / 3500
Chevy Suburban 2000–2006 Suburban 1500 / 2500
Chevy Tahoe 2000–2006 Tahoe, excluding the 2000 Tahoe Z71
Not compatible: GMC models or the 2000 Chevy Tahoe Z71.

OE/OEM reference numbers listed in the manual: 16526133, 16526134, 16524403, 16524404, 15199559 and 15199558. Confirm your vehicle and connector configuration before installation.

Before you start

Disconnect the main fuse or negative battery terminal before beginning work to help prevent accidental vehicle start-up and electrical short circuits.

If you do not have experience with automotive electrical work or headlight installation, seek professional assistance.

Check the connector diagram before making connections. Test the lighting functions before securing the replacement assemblies, and consult the troubleshooting section if a function does not operate correctly.

Install the headlight and turn signal assemblies

  1. Remove the original headlight assembly. Remove the retaining pin(s), pull the assembly outward and disconnect its wiring harness.
  2. Remove the original turn signal assembly. Locate and press the retaining clip, pull the assembly outward and disconnect the wiring harness.
  3. Connect and test the replacements. Connect the wiring harness to the new headlight and turn signal assemblies. Test all functions before proceeding.
  4. Protect the wiring and secure the assemblies. Secure and protect exposed wiring and connectors with heat-shrink tubing or fabric wire loom tape as needed. Install the assemblies using the factory mounting hardware and check that they are securely fastened.
BLH0002005 headlight retaining pin removal, turn signal clip release, harness connection and installation photographs
Installation photographs · Manual page 01. View full-size image ↗

Identify the wiring connections

Match the numbered leads to the BLH0002005 diagram before connecting the assemblies.

BLH0002005 headlight and turn signal wiring diagram identifying nine leads, including the side marker connector and DRL harness
Wiring identification · Manual page 03. View full-size image ↗
No. Connection No. Connection
1 Low beam 6 Turn signal
2 High beam 7 DRL jumper B
3 DRL jumper A 8 ACC/DRL connector
4 Side marker light 9 DRL fuse harness
5 DRL connector

DRL-to-ACC wiring

If the factory DRL connection does not activate the daytime running lights, the manual provides an alternative connection using the supplied DRL fuse harness and ACC power.

  1. Connect the high/low beam and turn signal connectors to the corresponding vehicle wiring harness connectors.
  2. Connect the turn signal ACC/DRL connectors to the matching connectors on the DRL fuse harness.
  3. Locate the under-hood fuse box. Use the manual's fuse table and photographs to identify the corresponding fuse slot, then insert the fuse tap as instructed.
Vehicle listed in the manual Fuse reference
1999–2002 Chevy Silverado 1500 / 2500 F67 (Cigarette Lighter)
2001–2002 Chevy Silverado 1500 HD / 2500 HD / 3500 F68 (Cigarette Lighter)
Tahoe, Suburban or another vehicle not listed in this fuse table? The manual does not specify its fuse reference. Contact customer support with your vehicle's year, make and model before choosing a fuse slot.
BLH0002005 DRL fuse harness connections, under-hood fuse box photographs and F67/F68 reference table
DRL-to-ACC wiring · Manual page 04. View full-size image ↗

Aim the headlights after installation

The manual describes a wall-based aiming procedure at 25 ft (7.6 m), using the vertical adjustment screw on the back of each housing. Prepare a level surface, remove excess cargo and check tire pressures before adjustment. Adjust one headlight at a time.

Read the complete procedure and diagrams on manual page 05 before aiming. If you are unfamiliar with headlight adjustment, seek professional assistance.

Troubleshooting

High or low beam does not work

The manual identifies connector polarity as a possible cause. Disconnect the high/low beam connector, rotate it 180°, reconnect and test again. Test each headlight individually.

The headlights stay in high-beam mode

The manual identifies a negative-switched headlight circuit as a possible cause. Contact support if the issue persists after connector polarity adjustment.

Only the upper or lower DRL illuminates in DRL mode

The manual recommends checking the DRL connector polarity: disconnect the DRL connector, rotate it 180°, reconnect and test again.

The lower DRL does not illuminate with the high or low beams

Check that the DRL jumpers are securely connected. The manual identifies a loose jumper connection as a possible cause.

The side marker light does not illuminate

Verify turn signal operation first. If necessary, disconnect the turn signal connector, rotate it 180°, reconnect and test again, as described in the manual.

If none of the lights operate after polarity adjustments, check the fuse and all wiring connections. Source: manual page 06.

Routine maintenance

Condensation

Temporary condensation may occur with changes in temperature and humidity. If water remains inside the headlight, accumulates or enters through a leak, discontinue use and contact support.

Cleaning

Wash with water and mild car soap when needed, then dry with a microfiber towel. Avoid abrasive cleaners or materials. Use plastic polish or wax only if it is recommended for automotive headlight lenses.

KEEP A COPY

Download the original installation manual

Open the original manual in a new tab to view, save or print the complete instructions and diagrams.

Car Light User Manual

BLH0002005 · English · PDF · 12 pages

VIEW / DOWNLOAD PDF ↗

Need installation support? Email contact@hawkglow.com with your vehicle's year, make, model and product SKU.

← Back to the Silverado / Suburban / Tahoe product